Should You Paint Your Brick House?
By Dunwoody Painters ·
Paint your brick house if the brick is sound and dry and you want the new color for good. Leave it bare if you might want the brick back, because paint is very difficult to remove from brick without damage [1], or if the wall shows white salts, flaking faces or open mortar joints. Limewash and mineral stain are the softer options we discuss at the estimate.
Why brick needs a coating that breathes
A brick wall takes in water and has to let it out again. The National Park Service explains that moisture migrates out of a masonry wall and evaporates, leaving any dissolved salts on the surface or just under it, and that salts crystallizing inside a brick create pressure that can make its outer face spall off [4]. A coating that blocks that evaporation turns a damp wall into a damaged one.
For that reason the Brick Industry Association recommends treatments that keep the masonry’s water vapor permeance high over ones that reduce it, and warns that a treatment that traps moisture can cause cracking and spalling [1]. Standard house paint traps moisture inside the masonry, so we use breathable mineral or elastomeric masonry coatings made for the substrate.
Paint, limewash, mineral stain or bare brick: how they compare
| Option | Look | Reversibility | Breathability | Upkeep |
|---|---|---|---|---|
| Solid masonry paint | Full coverage in one even color. | Very difficult to remove without damaging the brick [1]. | Acrylic latex paint is typically vapor semi-permeable, and heavy or repeated coats lower it further [1]. | A recurring task: repainting several times over the life of the brickwork [1]. |
| Limewash | A softer, mottled finish that lets the brick show through. It weathers, often forming streaks [1]. | Some limewashes can be removed with water within the first few days [1]. | Does not change the brick’s vapor permeability [1]. | Recoating is not difficult, because earlier coats do not have to come off [1]. |
| Mineral paint or stain | Changes the color while letting more of the brick show through. | Forms a chemical bond with the brick, so plan on keeping it [1]. | Does not affect the brick’s vapor permeability [1]. | It can go only on clean, unsealed brick [1]. |
| Bare brick | The brick and mortar as built. | Nothing to undo. | Unchanged. | None of the repeat coating that a treated wall needs [1]. |
Two notes on reading that table. Brick that is already painted is a different decision: the National Park Service says large areas of painted brick are best left painted, or repainted if necessary [3]. And if color is what you are weighing, our guide to exterior paint colors for Sandy Springs homes covers how to judge samples beside brick, roof and stone.
When brick should not be painted yet
Four conditions rule out a coating until they are fixed. All four are signs that water is in the wall.
- White salt bloom (efflorescence). The salts are left behind when water carrying them evaporates at the surface [2]. On a house more than a year old, they generally point to excessive water penetration or poor drainage, and coating a wall that tends to effloresce without stopping the cause may degrade the masonry [2]. We wash the salts off and neutralize them first, and the wall should be watched for them to return before it is treated [1].
- Flaking or spalling brick. Faces popping off mean moisture is trapped in the brick. Salts that crystallize inside masonry develop enough pressure to spall it, which is why a coating is not recommended as the only treatment for an efflorescence problem [2].
- Cracked or crumbling mortar. Mortar that is deteriorated, loose or missing, or cracked wider than the thickness of a business card, should be removed and repointed before any treatment [1]. We repoint failed joints first, so they are repaired and not filled with paint.
- Mildew that keeps coming back. Soiling on the exterior is a sign that excess moisture is present [1]. A power washing visit clears the growth, but the reason the wall stays wet has to be found before it is coated.
New work has its own wait. New or repaired masonry needs at least 30 days to cure and dry before it is treated, longer in cool weather, and brick that has just been cleaned needs at least 24 hours to dry [1].
How we help you decide before anything is painted
The decision is made on the wall, not on a chip. We walk the brick with you, note the problem areas, and brush color samples on the actual wall, because every mortar joint and rough face casts a small shadow and changes how a color reads. You check the samples in sun and in shade before you pick.
At the same visit we talk through limewash and mineral stains if you are not ready to commit to solid paint. Whichever finish you choose, windows, doors, walkways and plantings are masked and covered before washing starts, and failed mortar is repointed before the coating.
Every project carries a written 2-year workmanship warranty, and you pay nothing until the job is finished. The full scope is on our brick and masonry painting page, and there is more exterior advice in our painting guides.
Book a free brick painting estimate and we will put samples on your wall before you decide.
Sources
- Technical Note 6: Changing the Appearance of Brick Masonry (March 2025), Brick Industry Association.
- Technical Note 23A: Efflorescence, Causes and Prevention (June 2019), Brick Industry Association.
- Preservation Brief 6: Dangers of Abrasive Cleaning to Historic Buildings, National Park Service, Technical Preservation Services.
- Preservation Brief 2: Repointing Mortar Joints in Historic Masonry Buildings, National Park Service, Technical Preservation Services.
Not easily. The National Park Service says it is almost impossible to remove paint from masonry without causing some damage, and the Brick Industry Association does not recommend sandblasting because it damages the brickwork. That is why we talk through limewash and mineral stains as softer alternatives during the estimate.
It is better if you want an aged look and an easier way back. The Brick Industry Association says limewash does not change the brick’s vapor permeability, weathers into streaks by design, and can sometimes be removed with water in the first few days. Solid masonry paint is the pick for full, even coverage.
It can when the coating holds water in the wall. The Brick Industry Association says treatments that trap moisture can lead to cracking and spalling, and that acrylic latex paint is typically vapor semi-permeable and loses permeability with each heavy coat. A masonry coating that lets moisture evaporate, over a repaired and dry wall, is how that is avoided.
Not until the salts and their cause are dealt with. The Brick Industry Association says efflorescence should be removed and the wall watched for it to return before any treatment, and that efflorescence appearing more than a year after construction generally points to excess water or poor drainage. We wash and neutralize it before any coating goes on.
We use breathable masonry coatings from Sherwin-Williams and Benjamin Moore, mineral or elastomeric depending on the wall. Standard house paint seals moisture in, so we don’t use it on brick. The Brick Industry Association recommends an alkaline-resistant primer or a paint made for masonry, because mortar is chemically basic.
